FIREROL FRL-SW-1SU/FRL-SW-3SU A. Conductor B. Insulation Application-Used as power and control cable for protected installations inside and outside of rail and transport vehicles, where handling and installation cost are an important factor.-Used in control, auxillary and main circuit wiring such as cable harnesses, switchboards and control panels, driver desks etc. Construction Conductor Flexible tinned annealed copper wires, stranded as per HD 383 (IEC 60228) class 5 Insulation LSZH elastomeric compound as defined in EN 50264 -1 (EI 101 to EI 104) Electrical & Mechanical Properties Nominal Voltage 0.6 / 1 kV or 1.8 / 3 kV Maximum Conductor Temperature +90 deg (fixed installation) Minimum Permissible Ambient Temperature -25/-40 deg (fixed installation) Bending Radius 3 x Overall Diameter (D12mm) Chemical & Environmental Properties EN 60684-2 No fluorine EN 50305; EN 60811-2-1 Resistance to mineral oil & fuel oil, acid & alkali EN 50305 Resistance to ozone Fire Performance for rolling stock application EN 50306 -2 Hazard levels HL1, HL2/HL3, HL4 DIN 5510-2 Protection level 1/2/3/4 BS 6853 Interior use 1a, 1b, II; Exterior use 1a, 1b, II NF F 16-101 FO Fire Performance in general EN 50265-2-1; IEC 60332-1-2; NF C 32-070 2.1 (C2) Vertical flame propogation for a single insulated wire or cable EN 50266-2-4 + EN 50305; IEC 60332-3-24 ; NF C 32-070 2.2 (C1); VDE 0472 Teil 804 Vertical flame spread of vertically mounted bunched wires or cables EN 50268-2; IEC 61034-2; NF C 32-073; NF C 20-902; NF F 16 101; VDE 0472 Teil 816 Low Smoke Emission EN 50267-2-1; IEC 60754-1; NF C 32-074; NF C 20-454; VDE 0472 Teil 815 Halogen Free EN 50267-2-2 / 3; IEC 60754 -2; NF C 32-074; NF C 20-453; VDE 0472 Teil 813 Low Corrosivity (Acidity & Conductivity) EN 50305; NFX 70-100; NFF 63808; TM1-04; BS6853 Low Toxicity NFF 16101; NFF 63808; BS6853 Smoke index FRL-SW-1SU 0.6 / 1 kV NOMINAL CROSS-SECTIONAL AREA CONDUCTOR DIAMETER (a) MIN. MEAN THICKNESS OF INSULATION OVERALL DIAMETER WEIGHT RESISTANCE OF CONDUCTOR AT 20 ° C INSULATION RESISTANCE AT 20 ° C INSULATION RESISTANCE AT90 ° C min max max min min mm2 mm mm mm mm kg / km Ω / km MΩ · km MΩ · km 1.0 1.25 0.8 2.8 3.2 18 20 65 0.65 1.5 1.5 0.8 3.0 3.5 20 13.7 55 0.55 2.5 1.95 0.8 3.4 3.9 30 8.21 50 0.5 4.0 2.5 0.8 3.9 4.6 50 5.09 40 0.4 6.0 3.0 0.9 4.6 5.4 70 3.39 35 0.35 10 3.9 1.1 5.8 6.8 130 1.95 30 0.3 16 5.0 1.1 7.2 8.5 170 1.24 30 0.3 25 6.4 1.3 8.6 10 260 0.795 30 0.3 35 7.7 1.3 10.2 11.5 350 0.565 25 1.5 11.6 13.5 0.25 50 9.2 500 0.393 25 0.25 70 11.0 1.5 13.3 15.5 690 0.277 20 0.2 95 12.5 1.6 14.9 17.4 910 0.210 20 0.2 120 14.2 1.6 16.5 19.3 1120 0.164 20 0.2 150 15.8 1.9 18.5 21.7 1430 0.132 15 0.15 185 17.5 1.9 20.1 23.6 1720 0.108 15 0.15 240 20.1 2.1 22.9 26.8 2290 0.0817 15 0.15 300 22.5 2.2 25.4 29.7 2810 0.0654 10 0.1 400 25.8 2.3 28.7 33.6 2690 0.0495 10 0.1 (a) = for information, indicative only FRL-SW-3SU 1.8 / 3 kV NOMINAL CROSS-SECTIONAL AREA CONDUCTOR DIAMETER (a) MIN. MEAN THICKNESS OF INSULATION OVERALL DIAMETER WEIGHT RESISTANCE OF CONDUCTOR AT 20 ° C INSULATION RESISTANCE AT 20 ° C INSULATION RESISTANCE AT90 ° C min max max min min mm2 mm mm mm mm kg / km Ω / km MΩ · km MΩ · km 1.5 1.5 2.5 6.2 7.3 70 13.7 120 1.2 2.5 1.95 2.5 6.6 7.8 90 8.21 100 1.0 4.0 2.5 2.5 7.1 8.4 110 5.09 90 0.9 6.0 3.0 2.5 7.6 8.9 130 3.39 80 0.8 10 3.9 2.5 8.4 9.9 190 1.95 65 0.65 16 5.0 2.5 9.5 11.1 250 1.24 50 0.55 25 6.4 2.5 10.8 12.7 330 0.795 45 0.45 35 7.7 2.5 12.0 14.1 430 0.565 40 0.4 50 9.2 2.5 13.4 15.7 570 0.393 35 0.35 70 11.0 2.5 15.1 17.7 760 0.277 30 0.3 95 12.5 2.7 16.9 19.8 980 0.210 30 0.3 120 14.2 2.7 18.5 21.7 1210 0.164 25 0.25 150 15.8 2.7 20.0 23.4 1500 0.132 20 0.2 185 17.5 2.7 21.6 25.3 1800 0.108 20 0.2 240 20.1 2.7 24.1 28.2 2360 0.0817 20 0.2 300 22.5 2.7 26.3 30.8 2840 0.0654 15 0.15 400 25.8 2.9 29.8 34.9 3800 0.0495 15 0.15 a) = for information, indicative only